One of the ohm teminals may also be marked 75 ohm, with a line or some sort of marking “linking” it to the ground terminal. The ordinary cheap “T” FM antenna would connect to the 2 terminals marked ohm. Your speaker wire might make do til you can scrounge or buy a “T” antenna. Just take a 6 foot length or so and separate one end of it so the two ends are ” apart when spread out to the shape of a “T”. Separate the opposite end a few inches, strip the ends and attach to the ohm terminals. Try orienting the “T” in different directions for best signal. Should coaxial cable be involved Most amplified FM antennas have a coaxial cable with an “F” type connnector same as cable TV at the end. Some receivers have a “F” jack on the back for FM, so it’s just plug ‘n play. Otherwise, to eliminate the need to cut the connector off, strip the cable, etc.

Can someone show me how to hook up an FM antenna? Please!

Contest View Contest In this instructable i am going to shed light on a FM transmitter i had purchased from ebay a month ago. Like about feet in open space and if you were inside a building about 50 feet. Therefore i thought of doing something. But indeed i got some information about the gadget. Therefore i would like to share with Instructable. My primary Objectives would be as Follows:

Heads up! This tutorial was written for Si FM Tuner Evaluation Board V13 ().The V and GND pins are switched in the new revision. Make sure you connect to the correct pins for power if you are using an older version like V11 or the breakout board.

TV antennas have compromises built in.. All of this it tied together and the efficiency is greatly compromised. Also, there is no elements cut for the 3-meter FM broadcast band. You must rely on the VHF-lo elements, which are designed for Mc. This has directional selectivity limitations: Because the wavelength of the signal is too small for the VHF-lo elements, the antenna’s front to back ratio it’s ability to select signals directly in front of it, but reject signals from behind is very poor to nonexistent.

TV antennas tend to have many lobes, scattered around the azimuth plane, looking sort of like a starfish pattern, at Mc.

Suspicious Activity Detected

FM transmissions are line-of-sight. A hill, a coliseum, big buildings — all these things can get in the way of your FM reception and even leave you hearing the effects of multi-path interference. You get multipath interference when a signal meets an obstacle of some sort, such as a mountain. Depending on the broadcast strength, the signal might get absorbed or reflected by the mountain.

Due to these issues your radio will end up with poor reception as the different paths taken by the reflected signal arrive at your receiver at different intervals. Still, some people might experience all kinds of radio interference at home as well.

Dec 03,  · The cable hook-up runs through the same line as the antenna. So I would have to have the antenna down and the signal amplifier turned off if I was hooked up to cable. Then I wouldn’t get the benefit of the TV antenna for the tuner.

A lot of great content is accessible via the Internet, from sources like YouTube, Netflix, iTunes, and others. But will your old antenna work with modern, digital TV? In our case, the antenna was a large, s multi-directional behemoth that was hanging in our attic, unused for decades. However, my dad remembered it working quite well for analog TV, before cable was available in our area, so we decided it was worth the risk to try wiring it back up. For TV wiring, it converts old ohm twin-lead wire to new ohm coaxial wire.

If you have existing twin-lead wiring in good condition run to your TV, you can just use a balun where the twin-lead ends and a short length of coax to connect it to the TV. Otherwise, coaxial generally holds up better.

Can You Hook Up Two OTA TV Antennas?

Weather What type of feedline coax should I use for my antenna A common question that I receive is what type of coax cable should I use for my J-Pole antenna. This is a great question, as the coax you select can make a dramatic difference on the performance and range of your antenna system. There is a wide variety and choices of coaxial cable available and each type serves a different purpose. All coaxial feedline cables will exhibit signal loss.

The amount of loss is dependent on three factors, the construction of the cable, the frequency of the signal, and the feedline length. Balancing these variables is crucial in getting a solid signal out of your antenna system.

Antennas Direct offers high-performance outdoor TV antennas engineered to receive HD signals up to 70 miles from the broadcast towers.

I just ended up buying the beginnings of my first home theater on boxingday sales. Waiting until i move out of the apartment and into a house before i get the subwoofer and i’ll do without a center or matching surrounds untill the budget allows it. My question is about radio. The yamaha has a tuner and i get a few radio stations from it. It comes with both an FM and an AM antenna.

However i was under the impression that i could hook up my cable television to my receiver and get radio stations through it. I just want to make sure this is the case before i start connecting things. I do have a cable splitter. Should this work or will i destroy something? And if it does work, will i be able to receive any radio station that my car can get from just outside my building? Is it up to my cable tv provider as to what they transmit through the cable?

The website you were trying to reach is temporarily unavailable.

Many radios and most home stereo receivers include antenna terminals for the connection of an external antenna. Usually the supplied antenna is a minimalist design sometimes only an “internal” type, or as a telescopic rod or a short length of wire. This can be greatly improved for very little money outlay. All of the items needed are available from a local electronics store or hardware stores.

Steps 1 Determine the frequency of the station desired to be tuned.

one antenna on four bands is to work all states and Canadian provinces, along with Once the dipole is up, it’s time to test it. The first thing to do is listen for signals. If the band isn’t active, listen for natural or Wire Antennas for the Beginner.

Add an amplifier Open any radio with an AM section and you are sure to find a grayish black rectangular or round bar of metal, with wire wond around it on one end. This is the AM antenna. If you are not satisfied with your AM reception, you are probably wondering “is there anything I can do to improve it? The Ferrite Bar Your solution might be as easy as installing a larger ferrite rod. Ferrite is the grayish-black metal portion of the antenna. You have several things working for you:

How to Make a Simple Antenna to Improve the Reception of an FM Radio Receiver

This is how my antenna replacement worked for me and my SR5 4 cyl 4×4, your truck may vary! If in doubt, head to the dealer and ask for your specific diagram! As I couldn’t find any good pictures before I attempted this myself, I thought I would type them up to assist anyone else out there.

So if your antenna is designed for UHF/HDTV frequencies only, then it will not receive the FM broadcasts very well. But if it is a combined UHF/VHF antenna, with low-band VHF reception, then you should be able to receive the FM broadcasts.

Follow the 11 steps below to attach your antenna to a coaxial cable. If your antenna supports the coaxial cable, jump to step 8 directly. Step 1 — Buy the Grounding Block In case your antenna uses ribbon cables, you will need to buy a device that links the ribbon cables with the RF coaxial cable. Step 2 — Ground the Device To protect your home, you should ground the device you bought in Step 1.

Place a metal rod in the ground outside your home and screw the block into it. You will need to drill holes for this.

Outdoor FM Antenna Installation